Home › Plumber in Richmond Hill › Commercial plumbing › Plumbing Drawing Analysis & Quotes
Takeoffs & Quotes · Richmond Hill, ON · Updated November 2026

Plumbing drawing analysis and quotes in Richmond Hill.

Send the mechanical and architectural drawings and you get a written, itemized plumbing quote within 24 to 48 hours, with the conflicts flagged before they become change orders.

Copper supply manifold in a commercial unit by Seal Plumbing

How do you quote a commercial plumbing project?

From the drawings. We take off every fixture, drain, vent and water run from the mechanical and architectural sets, check them against each other and the Ontario Plumbing Code, and submit a written quote within 24 to 48 hours with exclusions and phasing stated clearly.

Commercial plumbing budgets go wrong when the quote was a guess. Seal Plumbing quotes Richmond Hill projects from the actual drawings: the mechanical set for drain, vent and water sizing, the architectural set for fixture locations, walls and finishes, and the structural set where slab work or risers are involved.

The analysis catches the problems early: a drain route that crosses a footing, a vent with nowhere to go, fixture counts that do not match between the sets, or a water heater that is undersized for the fixture load. We flag them in the quote so you can resolve them with the engineer before the price moves.

Quotes are itemized by phase, underground, rough-in and finish, so your general contractor can schedule around them. If drawings are not ready, we can quote from a site visit and a scope letter and update it when the set is issued. See the Richmond Hill commercial plumbing overview for the full scope we deliver.

What the quote covers

  • Fixture and equipment takeoff
  • Drain, vent & water line quantities
  • Conflict check between mechanical, architectural & structural sets
  • Code review before permit
  • Itemized pricing by phase
  • Written quote within 24 to 48 hours

How does plumbing drawing analysis & quotes work in Richmond Hill?

Drawings in, written quote out, within two business days.

1

Send the sets

Email the mechanical, architectural and, where relevant, structural drawings through the contact page, with the schedule you are working to.

2

Takeoff and review

We quantify every fixture, run and piece of equipment and check the sets against each other and the code.

3

Written quote

You receive an itemized quote by phase within 24 to 48 hours, with exclusions and flagged conflicts.

4

Review call

We walk through the quote with you or your GC and adjust for any changes to the scope.

Copper supply manifold in a commercial unit by Seal Plumbing
Supply manifold built from the drawings
Copper rough-in on a commercial wall by Seal Plumbing
Copper rough-in on a commercial wall

What does plumbing drawing analysis & quotes cost in Richmond Hill?

Drawing analysis and quoting in Richmond Hill is part of how we bid commercial work, not a separate charge. The quote you receive within 24 to 48 hours reflects the fixture count, the drain and water runs, the underground work and the equipment on the drawings, broken out by phase.

By phaseUnderground, rough-in and finish are priced separately so you can schedule and draw against each.
Exclusions statedWhat is by others, such as fixtures supplied by the owner, is written into the quote.
RevisionsIf the drawings change, the quote is updated against the new issue.

Commercial quotes are itemized by phase and submitted in writing within 24 to 48 hours of receiving the drawings. The written quote is the number that counts; changes to the drawings or scope are priced as change orders, also in writing.

What should Richmond Hill drawings show for an accurate quote?

Fixture counts, backflow protection, meter size and site servicing all belong on the drawings we quote from.

Backflow on the drawings

For an industrial, commercial or institutional building in Richmond Hill, the drawings should show where backflow prevention sits on the service and at any equipment that needs it. Under By-law 125-14 the devices are surveyed and tested, so getting them right on paper avoids rework.

Meter and site servicing

Richmond Hill expects plumbing to match the approved site service drawings when the meter goes in, and large meters need months of notice. If the site servicing and meter size are on the set, our quote covers the service entry correctly from the start.

Older buildings on Yonge

When the job is a renovation in an older building along Yonge Street, the existing drawings may be incomplete. We note what we need to confirm on site, such as the size and condition of the building drain, and price it clearly in the quote.

Send the architectural and mechanical drawings, the fixture schedule and any landlord requirements for your Richmond Hill unit. We review them, flag conflicts and send a written, itemized quote within 24 to 48 hours. If something is unclear, we ask you or your designer rather than guess at it.

Our Work

What does your recent commercial work look like?

Commercial rough-ins and fit-outs delivered from the drawings on recent projects. Tap a photo for a closer look.

See the full project gallery →

Which Richmond Hill areas do you serve?

Commercial and industrial units along the Highway 7 and Highway 404 corridors, in the Beaver Creek and Headford business parks, the Yonge Street storefronts, and projects across Vaughan, Markham, Aurora and the north GTA.

Yonge StreetHighway 7East Beaver Creek RoadBeaver Creek Business ParkHeadford Business ParkHighway 404 corridorLeslie StreetMajor Mackenzie DriveElgin Mills RoadCrosby Avenue

Commercial work across the GTA: see the main commercial plumbing page or all service areas →

Residential job instead? See our Richmond Hill plumber page.

Plumbing Drawing Analysis & Quotes nearby: Vaughan, Markham, Aurora and King City.

Plumbing Drawing Analysis & Quotes questions Richmond Hill businesses ask

Yes, as a starting point. Base building drawings for units in the Beaver Creek or Headford business parks usually show the stubs and services, and we add what your tenant layout needs. We note anything we must confirm on site before the price is fixed.
Yes. If the use calls for backflow protection, such as food service, medical equipment or process water, we note it in the quote, since Richmond Hill's By-law 125-14 requires those devices to be surveyed and tested.
The mechanical plumbing drawings and the architectural plans at minimum. Structural drawings help when slab cutting or riser penetrations are involved.
Yes, from a site visit and a scope letter, with the understanding that a mechanical design may be required for the permit. We say so in the quote.
Within 24 to 48 hours of receiving the drawings. Larger multi-phase projects may take the full 48 hours.
Yes. Conflicts between the sets, code issues and routing problems are listed in the quote so they can be resolved before work starts.
The quote is fixed to the drawings it was based on. Changes to the drawings or scope are priced as change orders in writing.

How do I get started?

Call 647-402-4825 or send your drawings through the contact page. Quotes on commercial work are submitted within 24 to 48 hours, in writing, from the mechanical and architectural drawings.