Home › Plumber in Richmond Hill › Toilet Installation
Toilets · Richmond Hill, ON · Updated November 2026

Toilet installation in Richmond Hill.

Replacing an old toilet, installing the one you bought, or adding a toilet where there was none. Standard, comfort-height and wall-hung, installed by licensed plumbers and leak tested before we leave.

Wall-hung toilet carrier roughed in by Seal Plumbing

How does a toilet installation work?

We confirm the rough-in matches your toilet, remove the old unit, check the flange and shut-off, set the new toilet level on a fresh seal and leak test it. A straight replacement is one short visit; a new toilet where there was none is a rough-in job.

A new toilet uses a fraction of the water an old one does and solves the running, rocking and weak-flush problems in one go. Seal Plumbing replaces toilets across Richmond Hill, from a straight swap in the same spot to a wall-hung unit on a new carrier in a renovation. If you have already bought the fixture, send us the model: we confirm the rough-in distance matches before we come and tell you before we start if anything will not fit.

Adding a toilet where there was none is a rough-in job we do all the time: a new powder room under the stairs, a basement bathroom, an ensuite in an addition. That means drain, vent and supply planned to the Ontario Plumbing Code, and a sewage ejector where the fixture sits below the main drain. Pete and Joseph quote it in writing first.

Wall-hung toilets need a carrier set solidly inside the wall before drywall and tile. We rough in the carrier during your renovation so the finished wall is clean and the unit is serviceable later. Our toilet installation guide covers what to look for when choosing one.

Toilet installation in Richmond Hill

  • Toilet replacement in the same spot
  • Supplied fixtures installed
  • Comfort-height & dual-flush upgrades
  • Wall-hung toilet carriers & rough-ins
  • New powder room & basement toilets
  • Flange repair & new shut-offs

How does toilet installation work in Richmond Hill?

Confirm the fit, remove the old unit, set the new one properly, test.

1

Get in touch

Tell us the toilet you have in mind or ask us to supply one. We confirm the rough-in and the fit.

2

Remove and inspect

The old toilet comes out and we check the flange, the floor and the shut-off before the new one goes in.

3

Install

New wax or waxless seal, toilet set level and secured, supply connected with a new shut-off if needed.

4

Test and clean up

Flush tested, checked for leaks at the base and supply, old toilet removed, area left clean.

Wall-hung toilet carrier roughed in by Seal Plumbing
Wall-hung carrier
Finished toilet and vanity installation by Seal Plumbing
Installed

What does toilet installation cost in Richmond Hill?

A straight toilet replacement in Richmond Hill runs $200 to $300 in labour. These are Seal Plumbing's estimate ranges as of October 2026, before tax; your written quote is the number that counts.

Toilet installation in Richmond Hill is quoted before we start, same-day for a straight replacement. The price depends on whether it is a swap in the same spot, a wall-hung unit on a carrier, or a brand-new toilet that needs drain, vent and supply roughed in.

Same-spot replacementThe low end: remove, reset, connect, test, old toilet taken away.
Wall-hung carrierThe carrier goes inside the wall during a renovation, before tile.
New locationDrain, vent and supply roughed in, with an ejector where the toilet sits below the main drain.

Every job is quoted before work starts, in writing for anything beyond a small repair, and the quote is the number that counts. Same-day quotes on most small jobs; larger projects within 24 to 48 hours of a site visit.

What should you check before a new Richmond Hill toilet?

Rough-in distance, the flange and the shut-off decide how simple a toilet swap will be.

Older bathrooms near Yonge

In homes in the village core and around Mill Pond, bathrooms may have been added or moved more than once over the years. We measure the rough-in and check the flange before you buy, so the new toilet fits the drain that is actually there.

Adding a basement toilet

Many 1990s and 2000s houses in Bayview Hill and Rouge Woods have basements still waiting to be finished. Adding a toilet there may need a sewage ejector if the drain is too shallow, so we check the depth of the main before quoting.

New locations need planning

Adding a toilet where there was none means new drain and vent work, unlike a straight swap in the same spot. We confirm with the City's Building Division whether your project needs a permit before we start, and build it to pass inspection.

Pick your toilet after we have measured the rough-in, since renovated older bathrooms in Richmond Hill do not always match the standard. We set it on a sound flange, add a new supply line and shut-off if the old ones are tired, test it and take the old toilet away.

What other plumbing services do you offer in Richmond Hill?

The same two licensed plumbers, across everything a Richmond Hill home needs.

Our Work

What does your recent work look like?

Toilets, carriers and finished bathrooms from recent jobs across the GTA and Simcoe County. Tap a photo for a closer look.

See the full project gallery →

Which Richmond Hill areas do you serve?

From Oak Ridges and Lake Wilcox on the Oak Ridges Moraine down to Langstaff and Doncrest at Highway 7, including Mill Pond, Crosby, Harding, Richvale, Bayview Hill, Rouge Woods, Jefferson, Westbrook and North Leslie.

Oak RidgesLake WilcoxMill PondCrosbyHardingRichvaleBayview HillRouge WoodsDoncrestLangstaff

Also serving nearby: Vaughan, Markham, Aurora, King City and Toronto. See all service areas →

Need something else? See our Richmond Hill plumber page or the full service and repairs overview.

Toilet Installation nearby: Vaughan, Markham, Aurora and King City.

Toilet Installation questions Richmond Hill homeowners ask

Yes. We plan the drain, vent and supply for the new room, check whether the existing stack can take it, and confirm permit needs with the City before we open the floor. We quote it in writing once the route is clear.
Usually, since the height does not change the rough-in. In condo suites on Yonge Street, the bigger questions are the drain position and whether the building has rules on renovation work. We check both before you order a new toilet.
Yes. Send us the model or the specs and we confirm the rough-in matches before we come. If anything will not fit, we tell you before we start.
Measure from the finished wall behind the toilet to the centre of the bolts holding it down. Most are 12 inches; some older Richmond Hill homes are 10 or 14. We check it on site.
Yes. Below-grade toilets need proper drainage, venting and sometimes a sewage ejector. See our sewage ejector guide and our basement plumbing page.
Yes, removal and disposal of the old unit is part of the job.
A straight replacement is usually a single short visit with a same-day quote. A new rough-in is quoted within 24 to 48 hours of seeing the site.

How do I get started?

Call 647-402-4825 or send a few details through the contact page. You get an estimated arrival time on the call and a written quote before any work starts.