Home › Plumber in Stouffville › Commercial plumbing › Concrete Scanning & Slab Cutting
Below-Slab Plumbing · Stouffville, ON · Updated November 2026

Concrete scanning and slab cutting for plumbing in Stouffville.

Before a drain goes under a commercial floor, the slab is scanned for rebar, conduit and cables, then cut and chipped cleanly along the planned route. One crew, one quote, from scan to backfill.

Underground drain trench in a commercial unit by Seal Plumbing

Why scan the concrete before cutting a slab for plumbing?

Scanning shows what is inside the slab before the saw touches it: rebar, electrical conduit, post-tension cables and existing pipes. Cutting blind risks a severed service, a structural repair or an injury. Seal Plumbing scans first, marks the route, then cuts and chips only what the new drain needs.

Adding washrooms, a commercial kitchen or floor drains to an existing Stouffville unit usually means opening the slab. Older buildings in Stouffville's historic Main Street village and industrial units in Gormley and Vandorf hide different things in the concrete, so we scan every cut line before the saw starts and mark conduit, rebar and existing drains on the floor.

The cut follows the drain route from the mechanical drawings, with the trench sized for the pipe, the bedding and the slope. We chip out the concrete, excavate to the invert elevation, set the drains and have the underground inspection passed before backfill and the slab patch. See commercial drain, vent and water line installation for what goes into the trench.

Because the same crew scans, cuts and installs, there is no hand-off between a cutting contractor and the plumber, and the quote covers the whole sequence. Dust control and site protection are part of the job on occupied buildings.

Concrete work we handle for plumbing

  • GPR concrete scanning for rebar, conduit & cables
  • Layout and marking of the drain route
  • Slab cutting with dust control
  • Chipping, excavation & bedding
  • Underground drain installation & inspection
  • Backfill, compaction & slab patch

How does concrete scanning & slab cutting work in Stouffville?

Scan, mark, cut, install, inspect, patch. Each step is done before the next so nothing is cut twice.

1

Scan and mark

The slab is scanned along the planned route and any rebar, conduit, cables or existing pipes are marked on the floor.

2

Cut and chip

The slab is cut to the trench width with dust control, chipped out and excavated to the drain depth.

3

Install and inspect

Drains are set to slope on proper bedding and the underground inspection is passed before anything is covered.

4

Backfill and patch

The trench is backfilled and compacted and the slab is patched flush, ready for flooring.

Underground drain trench in a commercial unit by Seal Plumbing
Trench cut for underground drains
Commercial drain stacks installed by Seal Plumbing
Stacks set above the new drains

What does concrete scanning & slab cutting cost in Stouffville?

Concrete scanning and slab cutting in Stouffville is quoted in writing with the underground plumbing it serves, within 24 to 48 hours of receiving the drawings. The price depends on the length of trench, the slab thickness, what the scan finds in the way and the condition of the subgrade.

Trench length and depthLonger runs and deeper inverts mean more cutting, chipping and excavation.
Slab thicknessThicker or reinforced slabs take longer to cut and chip.
ObstructionsConduit, cables or existing drains in the route change the plan and the price.

Commercial quotes are itemized by phase and submitted in writing within 24 to 48 hours of receiving the drawings. The written quote is the number that counts; changes to the drawings or scope are priced as change orders, also in writing.

Why scan the slab before cutting in a Stouffville building?

Industrial floors in Gormley and older Main Street buildings both hide services that a blind cut can sever.

Industrial floors

Units in the Gormley and Vandorf industrial areas may carry reinforcing, conduit and existing drains in the slab. Adding a trench drain or a washroom means cutting through it, so we scan the route with ground-penetrating radar and mark everything before the saw starts.

Older Main Street buildings

Buildings in the historic village along Main Street can have slabs poured and patched over many decades. Old pipes and abandoned services may sit where no drawing shows them. Scanning first shows what is there and keeps a storefront renovation from turning into a repair job.

Prestige industrial rules

The Gormley Industrial Secondary Plan includes a Prestige Industrial category that requires permitted uses to be carried out inside enclosed buildings. Plumbing for those uses runs under the floor, so clean cutting, dust control and a proper patch matter to the tenant.

Plan slab work for a time the space is empty if you can. If the unit is occupied, we set up dust control and schedule cutting around your hours. In Stouffville's business park buildings, ask the landlord for any slab drawings first, because they make the scan faster.

Our Work

What does your recent commercial work look like?

Underground drainage and commercial rough-ins from recent projects. Tap a photo for a closer look.

See the full project gallery →

Which Stouffville areas do you serve?

Commercial and industrial units in the Gormley and Vandorf industrial areas, the business park lands of urban Stouffville, the Main Street storefronts, and projects across Whitchurch-Stouffville, Markham, Richmond Hill and the north GTA.

Main StreetSandiford DriveGormleyVandorfStouffville GO areaHighway 48Ninth LineTenth LineMarkhamRichmond Hill

Commercial work across the GTA: see the main commercial plumbing page or all service areas →

Residential job instead? See our Stouffville plumber page.

Concrete Scanning & Slab Cutting nearby: Markham, Richmond Hill, Aurora and Newmarket.

Concrete Scanning & Slab Cutting questions Stouffville businesses ask

Always. We scan the cut line with ground-penetrating radar for rebar, conduit, cables and existing pipes, mark the safe route, then cut and chip only what the new drain needs. The underground work is inspected before backfill.
Yes. We scan first, cut with dust control and work around neighbouring tenants. Older buildings can hold surprises in the slab, so we price the cutting from the scan rather than from a guess about what is under the floor.
Yes. We schedule the cutting for the hours you set, contain dust and protect the surrounding finishes and equipment.
We stop and reroute. Cutting a post-tension cable is a structural problem, so the drain route is adjusted with the engineer before any cutting.
Yes. The trench is backfilled, compacted and patched flush so flooring can go down over it.
Yes. The underground plumbing inspection is booked and passed before the trench is backfilled.
Both. The same crew scans, cuts, installs the drains and patches, under one quote.

How do I get started?

Call 647-402-4825 or send your drawings through the contact page. Quotes on commercial work are submitted within 24 to 48 hours, in writing, from the mechanical and architectural drawings.