Home › Plumber in Brampton › Commercial plumbing › Concrete Scanning & Slab Cutting
Below-Slab Plumbing · Brampton, ON · Updated November 2026

Concrete scanning and slab cutting for plumbing in Brampton.

Before a drain goes under a commercial floor, the slab is scanned for rebar, conduit and cables, then cut and chipped cleanly along the planned route. One crew, one quote, from scan to backfill.

Underground drain trench in a commercial unit by Seal Plumbing

Why scan the concrete before cutting a slab for plumbing?

Scanning shows what is inside the slab before the saw touches it: rebar, electrical conduit, post-tension cables and existing pipes. Cutting blind risks a severed service, a structural repair or an injury. Seal Plumbing scans first, marks the route, then cuts and chips only what the new drain needs.

Adding washrooms, a commercial kitchen or floor drains to an existing Brampton unit usually means opening the slab. Older buildings downtown on Main Street and Queen Street and newer industrial units along the Highway 410 corridor hide different things in the concrete, so we scan every cut line before the saw starts and mark conduit, rebar and existing drains on the floor.

The cut follows the drain route from the mechanical drawings, with the trench sized for the pipe, the bedding and the slope. We chip out the concrete, excavate to the invert elevation, set the drains and have the underground inspection passed before backfill and the slab patch. See commercial drain, vent and water line installation for what goes into the trench.

Because the same crew scans, cuts and installs, there is no hand-off between a cutting contractor and the plumber, and the quote covers the whole sequence. Dust control and site protection are part of the job on occupied buildings.

Concrete work we handle for plumbing

  • GPR concrete scanning for rebar, conduit & cables
  • Layout and marking of the drain route
  • Slab cutting with dust control
  • Chipping, excavation & bedding
  • Underground drain installation & inspection
  • Backfill, compaction & slab patch

How does concrete scanning & slab cutting work in Brampton?

Scan, mark, cut, install, inspect, patch. Each step is done before the next so nothing is cut twice.

1

Scan and mark

The slab is scanned along the planned route and any rebar, conduit, cables or existing pipes are marked on the floor.

2

Cut and chip

The slab is cut to the trench width with dust control, chipped out and excavated to the drain depth.

3

Install and inspect

Drains are set to slope on proper bedding and the underground inspection is passed before anything is covered.

4

Backfill and patch

The trench is backfilled and compacted and the slab is patched flush, ready for flooring.

Underground drain trench in a commercial unit by Seal Plumbing
Trench cut for underground drains
Commercial drain stacks installed by Seal Plumbing
Stacks set above the new drains

What does concrete scanning & slab cutting cost in Brampton?

Concrete scanning and slab cutting in Brampton is quoted in writing with the underground plumbing it serves, within 24 to 48 hours of receiving the drawings. The price depends on the length of trench, the slab thickness, what the scan finds in the way and the condition of the subgrade.

Trench length and depthLonger runs and deeper inverts mean more cutting, chipping and excavation.
Slab thicknessThicker or reinforced slabs take longer to cut and chip.
ObstructionsConduit, cables or existing drains in the route change the plan and the price.

Commercial quotes are itemized by phase and submitted in writing within 24 to 48 hours of receiving the drawings. The written quote is the number that counts; changes to the drawings or scope are priced as change orders, also in writing.

When does a Brampton commercial job need slab cutting?

New washrooms, floor drains and trench drains in existing industrial and retail units usually mean cutting the slab.

Industrial floors with a new tenant

When a unit in the Bramalea industrial area or along Steeles Avenue changes tenants, new washrooms or a wash-down area often mean new drains under the existing slab. We scan the route for rebar, conduit and cables before any cut, and mark everything we find on the floor.

Retail and restaurant floors

A food tenant moving into a plaza unit needs floor drains, floor sinks and a grease interceptor below the slab. We cut, chip and excavate to the invert elevations on the drawings, set the drains and pass the underground inspection with the City of Brampton before the patch.

Working near a live building

In an occupied plaza or a running warehouse, cutting has to fit around operations. We use dust control, schedule the loud work with the landlord, and keep the trench open only as long as the inspection needs. Neighbouring tenants keep working while we do.

Ask for the scan results with the quote. GPR scanning shows rebar, conduit, cables and existing pipes, and moving a trench a few feet can save a lot of cutting. On Brampton industrial floors that have been through several tenants, the scan may find old lines that nobody drew.

Our Work

What does your recent commercial work look like?

Underground drainage and commercial rough-ins from recent projects. Tap a photo for a closer look.

See the full project gallery →

Which Brampton areas do you serve?

Commercial and industrial units across the Bramalea industrial area, Steeles Avenue and the Highway 410 corridor, the storefronts on Main Street and Queen Street, and projects across Peel Region, Caledon, Vaughan and Mississauga.

Bramalea industrial areaSteeles Avenue EastHighway 410 corridorAirport RoadHighway 50 corridorCountryside DriveQueen StreetMain StreetBramalea City CentreShoppers World

Commercial work across the GTA: see the main commercial plumbing page or all service areas →

Residential job instead? See our Brampton plumber page.

Concrete Scanning & Slab Cutting nearby: Bolton and Vaughan.

Concrete Scanning & Slab Cutting questions Brampton businesses ask

For a typical washroom group in an existing unit, scanning, cutting, chipping and setting the drains usually takes a few days, plus the time to get the underground inspection booked with the City of Brampton. We give you the schedule with the written quote.
Yes. We scan the route, cut and chip the trench, set the trench drain to slope on proper bedding and pass the underground inspection before backfill. The trench drain ties into the sanitary system or an interceptor as the drawings require.
Yes. We schedule the cutting for the hours you set, contain dust and protect the surrounding finishes and equipment.
We stop and reroute. Cutting a post-tension cable is a structural problem, so the drain route is adjusted with the engineer before any cutting.
Yes. The trench is backfilled, compacted and patched flush so flooring can go down over it.
Yes. The underground plumbing inspection is booked and passed before the trench is backfilled.
Both. The same crew scans, cuts, installs the drains and patches, under one quote.

How do I get started?

Call 647-402-4825 or send your drawings through the contact page. Quotes on commercial work are submitted within 24 to 48 hours, in writing, from the mechanical and architectural drawings.