Step into a curbless shower and nothing marks the edge except a change in slope. That is the whole trick. A curbless shower works when the floor drop, drain type and drain height are settled before framing changes, because the floor itself has to contain and steer the water. Leave those choices until tile day and the room either floods at the edge or gains a step it was never meant to have.
This guide covers the common ways to create the drop, how linear and point drains compare, and where the plumbing fits in the renovation sequence. It is written for Toronto homeowners planning an ensuite or main bathroom and the contractors building it.
Why the floor has to drop
A shower floor needs slope toward the drain. With a curb, that slope can sit on top of the subfloor because the curb contains the water. Without one, the shower area has to sit lower than the bathroom floor, or the bathroom floor has to rise around it, so the edge of the shower stays flush.
Manufacturer guidance notes that a curbless shower can depend on thoughtful floor preparation, integrated drainage and waterproofing designed to work together. Schluter's system overview describes that approach. In practice there are three common ways to get there:
- Recess the subfloor. The framing in the shower area is lowered between the joists so the sloped bed sits below the main floor. This depends on joist depth and direction and often needs structural input.
- Raise the surrounding floor. The rest of the bathroom is built up to meet the top of the shower slope. This avoids cutting framing but changes door thresholds and transitions.
- Use a sloped tray system. Prefabricated trays and ramps create the slope with less depth, but they still need a flat, sound base and the right drain body.
On a concrete slab, such as a basement, the drop means cutting the slab and recessing the shower area, with the drain set lower to match.
Linear drain or point drain
A point drain sits near the centre and the floor slopes toward it from every side, which calls for smaller tile or cut tile to follow the slope. A linear drain is a long channel at the back wall or across the entrance, and the floor slopes in one direction toward it. That single plane suits large format tile and makes a flush entry easier.
The drain choice changes the plumbing. A linear drain still needs a trap below it, and its outlet has to land between joists or within the slab cut. A drain across the entrance catches water at the edge but sits where people step. Look at the joist layout, the drain body depth and the tile plan together before choosing one.
We handle the linear or point drainage and slope coordination a curbless shower needs. Our ensuite installation work covers this alongside tubs, vanities and valves.
Where the plumbing fits in the sequence
Renovation plumbing should be planned before walls and finishes lock in the layout. For a shower without a curb, that means the floor approach, drain type and drain location are decided before framing changes, because the drain body is set to the height of the finished slope.
A typical order runs like this: structural changes to the floor, drain and trap set at the planned height, inspection, slope bed or tray, waterproofing membrane tied into the drain, then tile. The valve and shower head rough in happens at the same stage as the drain. In this kind of layout it makes sense to put the valve near the entrance so it can be reached without stepping into the spray.
Waterproofing and the drain flange
Waterproofing matters more without a curb, because water that escapes the slope has nothing to stop it. Many designers extend the membrane beyond the shower area into the bathroom floor. That decision belongs to the tile and waterproofing plan, but the plumber needs to know it so the drain flange suits the membrane being used.
Older Toronto homes need proper rough in planning to tie new fixtures into existing supply and drainage. A level entry shower on an older floor is a clear case. Our Toronto plumbing page covers that local work.
Plumbing questions from GTA renovations
Is a linear drain mandatory for a curbless shower?
A linear drain is not the only option, but it is often the easiest way to keep a flush entry with large tile. A point drain works when the floor slopes from all sides and the tile size suits that slope. The framing, the tile and the layout decide which one fits.
Can I convert my existing shower to curbless without gutting the floor?
Converting usually means opening the floor in the shower area, because the drain and slope have to drop below the bathroom floor. Some tray systems reduce the depth needed, but the subfloor, drain and waterproofing still have to be rebuilt. A site visit shows what the framing allows.
Code aware next step
Send your bathroom layout, the tile you are considering and a photo of the floor framing if it is exposed. We will tell you which floor approach and drain fit the room.
Send Seal Plumbing the project details through our contact page.